Vibration checker

Measure vibration with your phone. Free.

—mm/s

Peak velocity

Strength
Not measured yet
Frequency
— Hz · — RPM

Place your phone flat, screen up, on the thing that shakes.

Options30 s · mm/s
Stop after
Start delay

Time to put your phone in place after you tap Start.

Velocity unit
Acceleration unit

Your readings stay on your phone.

How to use it

This vibration checker turns your phone into a vibration meter. It reads the motion sensor that’s already inside your phone, right in your browser. You get three things in about 30 seconds: how strong the shaking is, how fast it is, and whether that’s normal.

  1. Place your phone flat, screen up, on the thing that shakes. A floor, a table, a washer lid, a machine housing. Take off a thick or soft case if you can, and make sure the phone can’t slide off.
  2. Tap Start. On iPhone or iPad, tap Allow when Safari asks for motion access. Then keep your hands off for the 2-second “Hold still…” step. It measures your phone’s own sensor noise so it can subtract it.
  3. Read the result. The live reading, a plain label and the frequency update as you watch. The test stops on its own after 30 seconds (you can pick 10 s, 60 s or no limit). You then get a chart, a one-line summary and buttons to save, download or share the result.

Testing something specific? The washing machine test, car vibration test and floor vibration test each give you placement tips and advice for that one job.

What the numbers mean

mm/s (millimeters per second) is the big number. It’s vibration velocity: how fast the surface moves back and forth. It’s the number most building and machine guidelines use. You can switch to in/s (inches per second). 1 in/s is 25.4 mm/s.

Hz (hertz) is how many times per second something shakes. A washer drum spinning at 1,200 RPM shakes about 20 times a second, so 20 Hz.

RPM is the same thing counted per minute: Hz × 60. It’s handy because motors, drums and wheels are rated in RPM. The Hz to RPM converter does the math both ways.

g is acceleration compared with gravity. 1 g is 9.81 m/s², the pull that keeps you on the ground. Shaking you can feel is usually a tiny fraction of 1 g. The details show acceleration as RMS (the average strength) and peak (the biggest single swing).

On this page, the label uses the estimated peak velocity (the RMS velocity × 1.41). Peak velocity is the measure Caltrans uses to describe how people react to vibration:

LabelPeak velocityWhat it’s like
Barely noticeableunder 0.25 mm/s (0.01 in/s)Most people won’t feel it
Noticeable0.25 to 1.0 mm/s (0.01 to 0.04 in/s)You feel it when you’re sitting or lying still
Strong1.0 to 2.5 mm/s (0.04 to 0.1 in/s)Clearly felt, often annoying
Very strongover 2.5 mm/s (0.1 in/s)Hard to ignore

These bands come from the Caltrans Transportation and Construction Vibration Guidance Manual (2020), human response to continuous vibration. Feeling a shake isn’t the same as damage. Caltrans guidance for possible damage to homes starts at much higher levels; see construction vibration limits.

Machine and appliance pages use a different scale, based on ISO 10816-1. The vibration severity chart explains it. The ceiling fan pages use a wobble scale made for slow-turning fans.

What it can and can’t measure

It works well for shaking between about 1 and 30 times a second. That covers washers on spin, ceiling fans, floors and footsteps, trucks passing by, and car wheels at highway speed. It also tells you the main direction of the shake: up-down, side-to-side or front-back.

It has real limits:

  • Fast vibration. Phones deliver about 60 samples per second, so the highest frequency they can measure is about 30 Hz. The exact limit for your phone is in the details. Faster vibration, like most electric motors and fridge compressors, can show up as a false lower frequency. When that seems likely, the tool says: “The main vibration may be faster than your phone can measure.”
  • Very slow movement. Sway under about 1 Hz, like a dryer drum turning, is too slow to read well.
  • Very faint vibration. If the reading is below 1.5 times your phone’s noise, you’ll see “No vibration detected.” That means it’s below what your phone can sense, not that nothing is there.
  • Sound. It measures shaking, not noise.

Phone sensors vary, and a case or a soft surface changes the reading. Treat every result as a good guide, not a certified measurement. For legal disputes, insurance claims or structural questions, hire a professional with calibrated equipment. How accurate is it? shows how the tool was tested.

Works on iPhone and Android

  • iPhone and iPad: Apple makes websites ask before they read the motion sensor, so Safari asks for Motion & Orientation access the first time you tap Start. Tap Allow. If you tapped Don’t Allow, the browser remembers that until you close it. Swipe Safari (or Chrome, Edge…) away in the app switcher, open this page again, tap Start and choose Allow. Opened from Instagram or Facebook? Open the page in Safari instead.
  • Android: there’s no prompt. It works best in Chrome or Samsung Internet. Firefox sends only about 10 readings a second, so it can follow slow sway, like a ceiling fan, but not machines or floors. If no reading appears in Chrome, open Settings, then Site settings, then Motion sensors, and make sure they’re allowed.
  • Laptop or desktop: most have no motion sensor. You’ll see a QR code that opens this page on your phone, and a Try demo button that plays sample data, clearly labeled as demo data.

The tool keeps your screen on while it measures, where the browser allows it. Switching to another app or tab pauses the measurement.

Private by design

Your readings never leave your phone. All the math runs in your browser, so there’s nothing to upload. There’s no app, no account and no signup. Saved images and CSV files go straight to your device. The house vibration logger keeps its logs in your browser only, with a Delete all logs button. The privacy page has the details.

All vibration tools

Pick the tool made for the thing that shakes. Each one sets the right scale, placement and advice. The calculators work on any device.

Home appliances

Cars and motorcycles

House, floors and construction

Machines and fans

Sensors and science

Calculators

Frequently asked questions

Can my phone really measure vibration?

Yes. Every smartphone has an accelerometer, the same motion sensor that turns the screen when you rotate the phone. It's sensitive enough to pick up shaking you can feel, and this tool subtracts the phone's own sensor noise first. The result is a good guide, not a certified measurement.

Do I need to download an app?

No. The vibration meter runs in the browser you already have, on iPhone, iPad and Android. There's no signup and nothing to install. If you use it often, add the page to your home screen.

What is a normal vibration reading?

It depends on what you're measuring. For floors and rooms, readings under 0.25 mm/s are barely noticeable to most people. Machines and appliances use a different scale, so use the matching tool page. The most useful comparison is often your own earlier reading of the same thing.

Why does it say "No vibration detected"?

The reading was less than 1.5 times your phone's own sensor noise, so the tool can't tell it apart from nothing. Put the phone flat on a hard part of the thing that shakes, not on a cushion or rug, and take off a thick case.

Does it work on a laptop?

Most laptops and desktops have no motion sensor. The page shows a QR code so you can open it on your phone, plus a demo with sample data. The calculators, like the Hz to RPM converter, work on any device.